Pianos consistently make movers annual list of products that are most frequently damaged. Grand pianos are specifically problematic. Practicing the following procedures for dismantling, padding and loading grand pianos will prevent damage, lower claims cost, and enhance consumer fulfillment.
1) A minimum of three people are needed to handle a baby grand piano. If the child grand piano needs to go up or down stairs or if a full or concert grand piano needs to be transported, a minimum of 4 individuals are required.
2) Constantly complete a comprehensive and accurate stock. It might be needed or more suitable to utilize a visual stock to effectively explain and show pre-existing damage.
3) As various parts are disassembled, please location all hardware in an effectively identified parts bag and then place the parts bag in a "Components Box".
4) Eliminate the music rack (lyre) from its track by pulling it towards the keyboard. Wrap it in a tidy furniture pad.
5) Disconnect the cover by eliminating the hinge pins. Have a single person wiggle the cover, holding it opposite the hinge, while a 2nd individual works the pin loose. Please be careful not to harm the wood with the pliers or with the pin itself. Cover the jaws of the pliers with a little cloth to assist prevent damage to the wood if essential. Wrap the lid in a clean furniture pad.
6) Eliminate the prop that holds the cover open and wrap it in a clean furnishings pad. The prop has a hinge pin and is in two pieces.
7) Get rid of the pedal assembly and wrap it in a tidy furnishings pad. The braces at the rear of the assembly rest in slots at each end. When eliminating the screws, please take care not to drop the braces. In addition, please be especially cautious with the push-rods so that they will not get bent. As you face the piano, number the push-rods from left to right as "1", "2", and "3", by putting a piece of masking tape with the suitable number on each rod. Keep in mind: If masking tape is not available, please usage properly identified parts bags for this function. When reassembling at location, please be sure to put the rods in this page the appropriate order so that the pedals will work appropriately.
8) Pad the piano by putting a clean rolled furnishings pad (stretch-wrap the pad to prevent it from unrolling) on the cover of the keyboard to avoid it from flopping open while you manage the piano. Keep in mind: Please ensure that the surface area of the piano is dust-free before padding it.
9) Position a piano board and connect the straps so that it is ready to get the piano. The raised brace on the piano board ought to be at the keyboard end of the piano.
10) Get rid of the left front leg by positioning one person beneath the piano at the left end of the keyboard. Be sure to have 2 individuals lifting the corner of the piano while the third person removes the leg. Note: Please be sure to note which legs were removed from which positions considering that some pianos have legs that are not interchangeable.
11) Location the piano on the piano board by decreasing the "leg-less" end onto the board. Please make certain to raise the whole piano a little while finishing this maneuver to prevent excessive pressure on the staying, connected legs as the piano suggestions. Lift the piano to an upright position on the board. Note: Please make sure that the soundboard is safe Visit Website and secure prior to lifting. Make sure that the piano is centered snugly versus the brace at the end of the piano board. Keep in mind: Never leave the piano unattended. Constantly have at least someone holding the piano stable at all times.
12) Remove the 2 staying legs and wrap them in clean furnishings pads. These legs are held in location by a "key and slot" plan. To remove the leg, slide it inward towards the center of the piano till it comes out of the slot.
13) Secure the piano to the piano board by bringing the ends of the straps together and securing them. Location folded burlap pads over the furniture pads however under the straps to supply additional security to the edges of the piano. To avoid the strap near the narrow end of the piano from slipping off, tie the loose ends of the 2 straps together.
14) To move the piano over a flat, level surface, tilt the piano and piano board and place a four-wheel dolly under the center of the piano board.
15) To move the piano up or down stairs, utilize the piano board as a skid. After adequately padding the stairs for protection against home damage, put the keyboard end of the piano towards the bottom of the stairs. Attach a hump strap to the leading end of the piano board to avoid the piano from slipping.
16) To fill the piano, leave it on the piano board and location it in a tier as the first base item with the keyboard facing the wall of the preceding tier. The best location to fill the cushioned cover is in between the piano and the preceding tier or in between the piano and the wall.
Grand pianos represent a substantial obstacle, they can be moved without damage by utilizing typical sense and practicing the procedures listed above.